Cold Resistance of Structural Steel Subjected to Cold Radial Forging

Metal Science and Heat Treatment - The structure, the strength characteristics and the impact toughness at different temperatures up to –100°C of tubular billets from steel 35 are...     

钢渣热焖工艺及其对水泥性能的影响

本文研究了不同的热焖压力和时间对钢渣活性的影响和钢渣的不同掺量对水泥性能的影响.热焖工艺主要改善的是钢渣的膨胀性,熟料的7 d膨胀率为0.034％,未热焖的钢渣掺入15％和35％时膨胀率分别增加155.9％和311.8％,而1 MPa 1 h热焖后,相比于未热焖的情况,钢渣掺入15％和35％时分别降低77.0％、89.3％,钢渣掺量25％时,其3 d、7 d、28 d 抗压强度分别增加8. 0 MPa、3.6 MPa、2.7 Mpa,分别提高21.1％ 、11. 3％ 、6. 1％.     

A mini review on two-dimensional nanomaterial assembly

Two-dimensional (2D) nanomaterials have attracted a great deal of attention since the discovery of graphene in 2004, due to their intriguing physicochemical properties and wide-ranging applications in catalysis, energy-related devices, electronics and optoelectronics. To maximize the potential of 2D nanomaterials for their technological applications, controlled assembly of 2D nanobulding blocks into integrated systems is critically needed. This mini review summarizes the reported strategies of 2D materials-based assembly into integrated functional nanostructures, from in-situ assembly method to post-synthesis assembly. The applications of 2D assembled integrated structures are also covered, especially in the areas of energy, electronics and sensing, and we conclude with discussion on the remaining challenges and potential directions in this emerging field.

     

Research on optimization design of PWR flow distribution device based on numerical simulation

ABSTRACT

In the lower chamber of pressurized water reactor (PWR), the flow distribution device is the core module to distribute coolant into the core. It has complex structure and numerous design parameters. Therefore, it has important theoretical and practical significance to optimize the device. The mesh independence verification, turbulence model selection, and data processing all can influence the numerical simulation results of the lower chamber, in order to research the influence, a numerical simulation method based on the original model of CNP1000 reactor lower chamber is proposed in this paper. In the method, an optimization design method of flow distribution device is established based on surrogate model. The main design variables and optimization objectives are determined based on the device’s structure and function characteristics. And then it respectively adopts Kriging algorithm and multi-objective genetic algorithm to establish a surrogate model of flow distribution device and optimize it globally. Finally, the optimal design variables are obtained. Compared with the device’s performance before optimization, the after optimization has smaller total pressure loss and more uniform flow. The effectiveness and practicability of proposed optimization design method can be verified.     

Influence of Sodium Microalloying on Rolling Contact Endurance and Mechanical Properties of Hot-Deformed Powder Steels

Russian Journal of Non-Ferrous Metals - Rolling bearing rings comprise a large reserve for expanding powder metallurgy production. This reserve is being incompletely implemented. The hot forging of...     

气体裂变产物88Kr半衰期测量

为准确测定气体裂变产物⁸⁸Kr的半衰期，本工作从辐照铀靶中分离得到3个放化纯的⁸⁸Kr气体测量源。以⁸⁵Kr作内标监督源，¹³⁷Cs或⁵⁷Co作外标监督源，使用多个HPGe探测器分别采用单探测器位置接力法和双探测器位置接力法跟踪测量⁸⁸Kr 196.3 keV能量的特征γ射线，跟踪时间均在8个半衰期以上，以获得其半衰期数据。对3次独立测量数据用多种方法进行处理，最终得到⁸⁸Kr半衰期测定结果为（2.796±0.015） h。     

泳池式轻水反应堆内电磁线圈可控温辐照装置设计

本文设计了在泳池式轻水反应堆（简称泳池堆）内在线测量电磁线圈电性能的可控温辐照装置。采用MCNP程序进行中子物理计算，对泳池堆、线圈骨架的结构尺寸与物质组分进行了精细全尺寸模拟，得出辐照装置的发热功率和中子注量率。通过初步估算，使用ANSYS CFX进行了数值模拟，得出辐照装置内线圈在堆运行时的温度，并提出温度控制的方法。辐照装置采用铝材加工制造，并进行了垂直度测试、气压测试、检漏测试。增加了绝缘设计，将辐照装置与泳池堆之间进行绝缘。在线圈处预埋铠装热电偶，对线圈温度进行实时监测。在泳池堆内对电磁线圈进行辐照试验，结果表明，本文设计的辐照装置能满足电磁线圈在泳池堆孔道内进行辐照试验的要求，并可对电磁线圈进行实时温度控制。     

MPE: a mobility pattern embedding model for predicting next locations

World Wide Web - The wide spread use of positioning and photographing devices gives rise to a deluge of traffic trajectory data (e.g., vehicle passage records and taxi trajectory data), with each...